LOTOS CT520D 50A Plasma Cutter 200A Tig Welder 200A Aluminum Stick Welder For Sale -

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder 200A Aluminum Stick Welder

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Buy Now

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder 200A Aluminum Stick Welder:
$399.50

Lotos CT520D Manual

General Overview

The LOTOS CT520D multipurpose units offer a variety of multiple welding and cutting aspects. It is able to cut all types of metal up to 1/2’’ with the 50A plasma cutting function. The hand carrying weight is 32 lbs, the unit is portable and reliable featuring a duty cycle of 60% at max amps on all NameCT520DFunctions50 A Plasma Cutter200 A TIG Welder200 A STICK WelderDimension with handleL x W x H17’’x 8’’x 14’’Weight32 lbs (14.5 kg)Input Voltage110-220 V, 1-PH, 50/60 HzHousing cutting torch50 A, 12.5 ft. (3.81m)TIG welding torch200 A 12.9 ft. (3.93m)Arc/Stick clamp200 A 6.5 ft. (1.98m)Argon regulator0-250 psiAir Regulator0-150 psiPlasmaCuttingRated input power requirement120-220 V, 1-PH, 27 A+/- 15%, 50/60 HzOutput current10-50 A @220V10-25 A @110VDuty cycle @ 40°C (104°F)60% @ 50 A100% @ 40 AGas supplyClean, dry, oil-free airRecommended gas inletflow rate / pressure3.6 scfm @ 65 psi80L/minMax Rated Cutting Thickness1/2 inches (12.7mm)

DC

TIGWelding

Rated input power requirement120-220 V, 1-PH, 17 A+/- 15%, 50/60 HzOutput current10-200 A @ 220V10-100 A @ 110VMaterial can weldSteel, Stainless, Moly, FerrousDuty cycle @ 40°C (104°F)60% @ 200 A100% @ 150 ANo load voltage62 VWorking Voltage16.9 VGas supplyClean, dry, oil-free argon gasStarting MechanismHigh Frequency Start / HF WeldingRecommended gas inletflow rate2-5 L/M

DC

StickWelding

Rated input power requirement120-220 V, 1-PH, 23 A,+/- 15%, 50/60 HzOutput current10-200 A @ 220V10-80 A @ 110VMaterial can weldingSteel, Stainless, Moly, FerrousDuty cycle @ 40°C (104°F)60% @ 200 A100% @ 95 ANo load voltage62 VWorking Voltage25 VStarting MechanismHigh Frequency Start / HF Welding

CONTROL PANEL

Applicable Torch TypeTorch TypeModelAmperageConsumables Type5 prong LCON cutting torchCL010550

LCON0120

LCON0140

LCON0190

Extended 5 prong LCON cutting torchCL020550

LCON0220

LCON0240

LCON0290

Applicable Consumables PackagePart NumberNozzleElectrodeShield CupSwirl ringPackage TypeTotal PiecesLCON0120LN01LE01LC01LR01LN01 x 10,LE01 x 1020LCON0140LN01LE01LC01LR01

LN01 x 10,

LE01 x 10,

LR01 x 10,

LC01 x 10

40LCON0190LN01LE01LC01LR01LN01 x 40,LE01 x 20,LR01 x 20,LC01 x 1090LCON0220LN02LE02LC02LR02LN02 x 10,LE02 x 1020LCON0240LN02LE02LC02LR02LN02 x 10,LE02 x 10,LR02 x 10,LC02 x 1040LCON0290LN02LE02LC02LR02LN02 x 40,LE02 x 20,LR02 x 20,LC02 x 1090Unrivaled QualityThe production process for Lotos products is among the most stringent in the world and meets or exceeds some of the industry's most rigid standards. Our studies show that it is in fact among one of the best in the industry and is unrivaled by other would-be competitors. The quality of each of the integrated components is constantly monitored during the course of production. Only components and materials that meet the highest industry standards for quality are permitted to be incorporated into our LOTOS line of products. Finally, upon conclusion of production, each unit is put through a newly devised, far more rigorous 30 point testing and quality inspection routine. This process is critical to ensuring a product that is not only safe, but reliable in both performance and durability.

Cut at 12 Times the Speed of Sound

Plasma cuttingis a process that is used to cut steel and other metals using a plasma torch. In this process, an inert gas (compressed air) is blown at high speed out of a nozzle; at the same time an electrical arc is formed through that gas from the nozzle to the surface that is being cut, turning some of that gas to plasma. The plasma is sufficiently hot to melt the metal being cut and moves sufficiently fast to blow molten metal away from the cut. The plasma, which is maintained between the work-piece and electrode, travels at over 9000 MILES PER HOUR (15,000 km/Handle). That’s over twelve times the speed of sound.

Advantage of Plasma vs. Oxy-Fuel Torch

Plasma does not use expensive, hazardous gases, only compressed air. It imparts much less heat into the piece being cut, eliminating warping. It does not require ignition. It leaves little to no slag to clean up or grind off. The cost per cutting hour can be less than oxy-fuel since there is no gas cost. It is also much quicker and easier. So, you cut better, faster and inexpensively.

Skill and Training

There is not a lot of skill or training required to operate aplasma cutter. The torch should remain at a 90-degree angle.ADVANCED INVERTER TECHNOLOGYThe CT520D inverter rectifies the input voltage (110V or 220V) into DC (Direct Current), which is then fed into a series of MOSFETs (Metal Oxide Semiconductor Field Effect Transistor). LOTOS LT5000D/CUT50D utilizes the most advanced TOSHIBA MOSFETs. These MOSFETs (transistors) are switched at thousands of Hertz, which greatly reduces the magnetic flux, and therefore the size of the transformer. Hence, the use of MOSFETs allows for a compact and light weight machine such as the CT520D to operate at its performance parameters. In simple terms the use of these MOSFETs makes it possible for CT520D to produce the necessary power, using very little space and creating minimal heat dissipation.PaymentWe accept Paypal, Credit cards (Visa/Master/Discover/American Express), Money Order or Checks. Pleasecontact usif you have any questions. International customers, please contact us for shipping fees.Shipping and TrackingFREE FedEx shipping with FREE tracking information to 48 states. Additional Shipping Info:

  • Priority mail (2 to 3 days) is $39
  • FREE tracking information
  • Canada FedEx Ground: $39
  • Canada Priority Mail Shipping: $79
  • International Priority mail (to European countries and Mexico, Brazil): $120
  • International Priority mail (to Australia): $160
  • We try our best to ship the item within 2 business daysafter payment is received (most of time within 1 business day)
  • FedEx does not ship to a PO Box address, you have to use priority mail to ship large packaging to a PO box address

WARRANTY, SERVICE and PARTSWarranty Terms:Lotos Technology warrants that all equipment sold by our company, unless otherwise specifically stated, will be free from defects in materials and workmanship for a period of 1 year from date of shipment. Such warranty shall not apply in any event to failure or defects in materials due to normal wear and tear, failure to perform recommended or customary maintenance procedures, exposure to detrimental elements, improper storage, or corrosion, and shall not extend to any person or entity other than the customer. To purchase an extra 3 years' warranty, please clickhere.

Return:After shipment, product is returnable for a refund within 30 days of shipment, with a minimum 20% restocking fee. Lotos Technology reserves the right to charge a restocking fee higher than 20% based on the condition of products received. Original shipping and handling fee is not refundable. Feel free tocontact usif you have any questions or comments.

Useful Information for Lotos (BL)CT520D:

Here is the video link for machine setup and operation.

a better user manual is online now, check following link (and thanks to Anthony, our Canadian dealer)

For Plasma Cutting

For your convenience, the initial consumables are included in the package. However, you may need extra consumables/parts for your project. We provide the following three packages for our customers-

LCON40

LCON90

LCON150


Buy Now


Related items